Ziggy587 wrote:Personally, I think it would look better with out the sprites.
i was thinking the same while doing it... going to upload it that way too..
ziggy BTW i see you are the man to ask.. im looking at a willem True-USB PRO GQ-4X Willem Programmer Light Pack with the complete TSOP pack..also an uv eraser.. do i need something else to start doing repros?... im going for snes, nes, and genesis repros... any advices?
Ziggy587 wrote:Well right off the bat I can tell you that you'll need a 16-bit adapter for Genesis and some SNES games.
im posting the kit and the programmer.. as i see some 16bit/8bit adapters for tsop... but im not 100% sure if im missing the one you said
the tsop kit has: http://www.mcumall.com/comersus/store/c ... oduct=4426
1.ADP-083 TSOP32 base board
2.ADP-071 FWH-TSOP32-TSOP40 2-in-1 base board,
3.ADP-082 TSOP40A/B 2-in-1 base board,
4.ADP-072 TSOP48(16/8bit) base board
5.ADP-073 TSOP48(16bit) base board.
6.ADP-077 TSOP48 ZIF socket top board
7.Address wires
You don't need that entire package. You only need the top piece and one bottom piece. Also, for THOSE adapters you need to get another adapter for the GQ-4x for the extra address wires. But, I think MCUmall makes a new TSOP adapter that works on the 4x with out the need for the extra adapter.
But what I was referring to was a 16-bit adapter for 16-bit EPROMs. You'll need one for Genesis carts and some SNES carts as well.
ADP-077 TSOP 20mm adapter set top ZIF board
This base board is for TSOP32,TSOP40,TSOP48 20mm body width chips. It works with a any TSOP adapter base board.
For eproms 16bit ADP-054 16 Bit EPROM 40/42 pin ZIF adapter V3 for Willem :It has on board both DIP40 and DIP42 ZIF sockets and 2 PLCC44 sockets on board. So that be able to support both DIP and PLCC package 16 bit EPROMs easily.
Device supported on ZIF socket:
27C1024,27C2048, 27C4096,27C210,27C2002,27C4002,27C400, 27C800, 27C160, 27C322.
The adaptor set also includes 42 pin EPROM address wires for all 32 pin ZIF Willem programmer. For GQ-4X does not need address wires.
the rest of eproms that i should use are covered by the device itself, right? (genesis, nes and snes projects)
about the eproms im looking for
Snes covered by:
M27C322 for 32mbit (use 16bit adaptor right?)
27C801 for 8mbit
29F032 for tsop
74ls139 2to4 line adress decoder for multi eproms
16bit to 8bit bus: 74_245, 74_139
genesis covered by:
M27C322
NES covered by:
27C64
27C128
27C256
27C512
27C010
27C020
27C040
btw ziggy what schematics did you use for tsop to snes? the romlaboratory or the one at nesdev?.
is something im missing here? or that you recommend?
BTW I saw that they have to be between 100 and 150ns on speed side... safest way is going for 120ns this is a fact right?
Last edited by juanmiglesias on Fri Jun 25, 2010 3:08 am, edited 1 time in total.
im doing the order tonight. 
