hi im new to the forums not sure where to put this but anyway
anyone know where i can find rgb/vga on a imac slot loading g3 it has no mother board all thats left of it is the shell, screen and the board that goes to the screen
iMac VGA / RGB Question...
Re: imac
I don't think it will have video connections since the monitor is built in.ccm wrote:hi im new to the forums not sure where to put this but anyway
anyone know where i can find rgb/vga on a imac slot loading g3 it has no mother board all thats left of it is the shell, screen and the board that goes to the screen
Support Racketboy on Patreon
Follow Racketboy on Social: Instagram / Twitter / Facebook
Subscribe to Email Newsletter (Blog / Guide Updates Every Week or Two)
Follow Racketboy on Social: Instagram / Twitter / Facebook
Subscribe to Email Newsletter (Blog / Guide Updates Every Week or Two)
- lordofduct
- Next-Gen
- Posts: 2907
- Joined: Sat Apr 01, 2006 12:57 pm
- Location: West Palm Beach
Yeah the built in monitors utilize direct digital transfer over to the monitor.
As long as it has an LCD display (i.e. like the lap tops and the sort) you aint gonna get it with out spending hundreds of dollars on parts. (mainly a analog to digital converter)
Now if you happen to have one of the CRT monitors you can hack the machine up to make it accept VGA. All CRT monitors are inherrently analog and use the RGB signalling to display picture. When the computer digitally sends the information over to the monitor there is a device that turns the digital signal into the RGB component.
What you'll have to do is locate said device, figure out what pins are the ouputs of the RGB colour and sync signals, then rip off the device. Next you will have to find out what frequency ranges it supports and mostl likely hook up an analog receiver in the bastard to clean up the VGA signal you send to it (unless you decide to send pure RGB which could be hooked directly to these lines as long as it is in the correct frequency range).
And well... all in all... it is a waste of time, difficult to perform... and most of all DANGEROUS.
I do not advise pulling apart a monitor and fucking around with its guts unless you know what everything is and what it does. A mistake and the bitch could electricute you or worse the CRT could explode.
As long as it has an LCD display (i.e. like the lap tops and the sort) you aint gonna get it with out spending hundreds of dollars on parts. (mainly a analog to digital converter)
Now if you happen to have one of the CRT monitors you can hack the machine up to make it accept VGA. All CRT monitors are inherrently analog and use the RGB signalling to display picture. When the computer digitally sends the information over to the monitor there is a device that turns the digital signal into the RGB component.
What you'll have to do is locate said device, figure out what pins are the ouputs of the RGB colour and sync signals, then rip off the device. Next you will have to find out what frequency ranges it supports and mostl likely hook up an analog receiver in the bastard to clean up the VGA signal you send to it (unless you decide to send pure RGB which could be hooked directly to these lines as long as it is in the correct frequency range).
And well... all in all... it is a waste of time, difficult to perform... and most of all DANGEROUS.
I do not advise pulling apart a monitor and fucking around with its guts unless you know what everything is and what it does. A mistake and the bitch could electricute you or worse the CRT could explode.
-
metaleggman
- 128-bit
- Posts: 894
- Joined: Sat Nov 04, 2006 7:21 pm
OR IMPLODE!lordofduct wrote:I do not advise pulling apart a monitor and fucking around with its guts unless you know what everything is and what it does. A mistake and the bitch could electricute you or worse the CRT could explode.

- lordofduct
- Next-Gen
- Posts: 2907
- Joined: Sat Apr 01, 2006 12:57 pm
- Location: West Palm Beach
- lordofduct
- Next-Gen
- Posts: 2907
- Joined: Sat Apr 01, 2006 12:57 pm
- Location: West Palm Beach